Smart Safety Hook Detector SHD-100
According to Ministry of Labor statistics, falls from height are the leading cause of fatal accidents on construction sites. The most common on-site scenario: workers wear a safety harness but do not clip the hook to an anchor point. The SHD-100 uses a dual detection mechanism of magnetic sensing + barometric altimeter: when the height exceeds 2 meters and the hook has not been attached for more than 15 seconds, it immediately issues a voice alarm and notifies the supervisor, with the whole process from detection to notification taking no more than 20 seconds.
Key Performance Indicators
IoT Smart DetectionInternational Certifications
Meets regulatory requirementsRepublic of China national standard for personal fall protection equipment connectors (hooks); meets OSHA regulatory requirements in Taiwan and can serve as a basis for compliant procurement.
EU safety certification, compliant with the European Personal Protective Equipment Regulation (PPE Regulation EU 2016/425), suited to compliance requirements of multinational projects and foreign-owned sites.
European standard specification for personal protective equipment connectors, used together with CE certification to ensure hook structural strength and the opening/closing mechanism meet international safety standards.
Hook Safety Detection Flow
Whole process ≤ 20 secondsAfter power-up, the device takes the current position height as the relative zero (0m). Whatever floor it is powered on at, that position is the baseline height. The console shows hook status in real time; the device itself raises no alarm at this point.
When a person climbs more than 2 meters above the power-on baseline, the device enters hook monitoring mode automatically.
If 2 meters is exceeded while riding an elevator, the system detects hook status;
while the elevator is moving you can hold the hook's magnetic sensing area by hand to pause alarms, and monitoring resumes when you release it at the work level.
When the height exceeds 2 meters and the hook has not been properly fastened for more than 15 seconds:
Once the person fastens the hook properly, the device stops the voice alarm at once, the console status updates to "Compliant" automatically, and the event record is archived for reference.
The SHD-100 supports a double-hook design. Scaffold work usually needs a single hook; for high-risk environments such as H-beams and steel structures, double hooking is recommended.
The alarm stops only when both hooks are fastened; if only one is fastened, the unfastened one keeps reminding, ensuring safety compliance in double-hook work areas.
Common Work Scenarios
Real-world Q&AAfter the elevator rises more than 2 meters the system starts detecting hook status. If the hook is not yet attached while moving, you can hold the hook's magnetic sensing area by hand to suppress the alarm temporarily; after you reach the work level and attach the lifeline, release it and the alarm clears automatically.
Height is relative, with the power-on position as zero. Whether powered on at floor 1 or floor 20, rising more than 2 meters triggers monitoring; there is no need to set an absolute floor height, so it adapts flexibly to all work environments.
No. The SHD-100 uses Cat.1 4G communication, sending sensor data and alert signals with very low data needs; an ordinary industrial IoT SIM card is enough, and no video-streaming-grade data plan is needed.
Currently the SHD-100 focuses on hook attachment status detection (unfastened hook alarm, low-hook-high-use alarm, SOS alarm); sensing whether the harness itself is buckled is not yet supported and is a planned future feature.
Nine Core Functions
When height exceeds 2 meters and the hook stays unfastened for 15 seconds, the device announces by voice every 5 seconds while the management platform pops up a notice at the same time, all within 20 seconds.
When the anchor point is detected below the shock-absorber position, a "working high, anchored low" warning is issued immediately, guarding against protection failure from wrong anchoring, the most commonly overlooked hazard on sites.
Takes the power-on position as the relative zero and starts monitoring automatically beyond 2 meters, returning ambient temperature at the same time so the console knows the on-site conditions.
Know each high-altitude worker's exact position in real time, with track playback and electronic fence management on the console, for fast location and rescue in an accident.
One-press call to the command center with real-time two-way voice intercom, so workers doing solo work at height always have someone tracking their status.
The G-sensor senses abnormal impact, issues an emergency alarm automatically and uploads an event record, giving first-hand data for accident investigation.
Supports multi-range voltage sensing from 220V to 220kV and alerts automatically when a person approaches high-voltage cables, suited to transmission line and telecom tower construction.
Triggers an alert automatically when the device stays still too long, so unconscious or trapped workers do not go unnoticed, providing additional life safety protection.
Managers set no-entry or no-exit zones, and the device and platform warn in sync, preventing people from entering hazardous areas by mistake or leaving the work area without permission.
Applications
Technical Specifications
Need an assessment for a hook detection solution for work at height?
We provide free site assessments and plan the most suitable configuration for your work environment (H-beams / scaffolding / steel structures).